Maintenance tips for Yamaha Propellers

Yamaha Propellers undergo rigorous wear and tear after which it becomes important to maintain.
In this blog post, we will discuss some maintenance tips for Yamaha Propellers.
  1. Inspect your Yamaha Propellers regularly – It is important that you inspect your lower unit now and then. Remove the prop and apply marine grease to the Yamaha propeller shaft. Remove the lower drain plug and check the color of the lubricant, if it's white then water presence is there in your gearcase. Disassemble your propeller’s lower unit and replace the seal before using your outboard again.

  2. Change the gear lube of your Yamaha Propellers – It is easy to change the lubricant yourself. It is ideal if you rely on a dealer. Make sure you also replace the vent and drain screw seals each time.

  3. The battery in your Yamaha Propellers – Make sure to use the recommended size of the battery. Don’t compromise with the battery. Apart from that, consider adding one or two house batteries to power accessories.
  4. Use fogging oil in your Yamaha Propellers – Use fogging oil as it protects internal components of an engine that are vital during inactive. It prevents rust and corrosion and also protects them during start-up when the outboard is returned to service.
  5. Keep your Yamaha Propellers Dry – Make sure to keep your Yamaha Propellers dry as water can enter in the fuel system during extended storage periods. With that, make sure to lower the engine fully and place a sealed plastic bag over the lower unit to help prevent moisture.
Location: United States

Comments

Post a Comment

Popular posts from this blog

Zinc Anodes: Get the Ultimate Protection for Your Boat, Big or Small

Image
Mixture of different metals getting in touch with salt water provokes corrosion. Without getting too technical, zinc anodes protect metals on the boat exposed to the harsh underwater environment by being the most likely to corrode. Basically, the zinc anodes corrode before the boat does, saving you costly repairs and headaches. Note that zinc anodes only work when they are electrically connected to the items they are intended to protect. The zinc anodes will be set up as part of ships’ bonding system and will be connected inside the boat via the long bolts.  Components of Boat Zinc Anodes Protect There are a variety of metals on your boat’s hull with salt water all around. A typical boat probably has some stainless steel (prop shafts and other components), different varieties of bronze (propeller, thruhulls etc) and possibly aluminum (outboard motor or outdrive components). With these different metals in salt water you get what amounts to a battery action. The di...
Read more

How to improve Michigan propellers efficiency?

Image
Before knowing how to improve it is important to note that a propeller is no more than a set of rotating wings. In this blog, we will discuss how to improve the efficiency of Michigan propellers. The first and foremost thing that comes into play is that boats that benefit from lowering trim tabs considerably at cruise rpm might see big gains from foil propellers. It is because the downward angle of propeller shafts on most inboard-powered planning powerboats helps propellers lift the stern without the added drag of lowered tabs. It is also important that propeller blades raked increase stern lift by shifting the center of effort of that lift in relation to the fore-and-aft center of buoyancy of the boat. Noise, Vibration, and Cavitation Noise and Vibration of propeller come from Cavitation. To eliminate noise and vibration, simply adding the blades will do the work. Cavitation typically occurs as each propeller blade passes through the wake of the running gear and ...
Read more

Premium Quality Lasdrop Shaft Seal on Sale for Easy Troubleshooting

Image
Getaprop Lasdrop shaft seals are the answer for an easily installed replacement to the original stuffing box on nearly any boat. Once installed, there is virtually no maintenance required. The original stuffing box models will last as long as eight to ten years before servicing while the Lasdrop Shaft seal will last three to five years before the inner lip seal must be changed. At the service interval, both the original and generation-II Lasdrop shaft seal models would most likely require refurbishing of the seal surfaces. Additionally, the bellows on the original model should also be inspected and replaced if found necessary. Lasdrop Shaft Seal – A Greener Solution for Boat Industry Lasdrop shaft seals are truly the green solution to preventing contaminated bilge water from entering the ocean you are in. Whether you are running a research vessel, a flashing boat, a world cruising sailboat or a workboat, keeping the water you run in clean is a good practice. Remember, ke...
Read more